Messages

1

Do You Need Help? Post it here / Re: lor shutdown

« on: December 09, 2019, 08:38:13 AM »

Sorry Keith, its lor hardware controller with xlights. I have a mixture in this particular display..
and I have it set-up where all the 16chnl lor controllers are on there own network.
There is a mixture of lor legacy, lor ccb, and a bunch of diy falcon controlled fixtures.
but what shut down on us is just the lor 16chnl ac controllers network comm port.
tried 2 other comm ports, and they would start out good, till I ran xschedule, then they go red in the scheduler, and I'd loose communication with them

2

Do You Need Help? Post it here / lor shutdown

« on: December 08, 2019, 09:31:01 AM »

updated to ver 69 (thanks Keith), and ran a show. the network my lor legacy channels all shut down. they were on there own network. tried different comm port, which fixed its communication, till I ran a show again, and it shut down again
got the following after each shutdown

3

Do You Need Help? Post it here / scheduler shutdown

« on: December 05, 2019, 06:27:09 PM »

I get a scheduler shut down during a show and the log shows an application error, which I know nothing about.

4

Do You Need Help? Post it here / Re: xschedule videos

« on: November 27, 2019, 03:50:00 PM »

Thank you Gil, thank you Keith
I unchecked it and that solved it

5

Do You Need Help? Post it here / Re: xschedule videos

« on: November 27, 2019, 09:36:47 AM »

Thanks Gil, thought I had, but it had been several hours in front of this screen, with several frustrating interruptions.
I'll check it out

6

Do You Need Help? Post it here / layout fixture zoom

« on: November 27, 2019, 09:33:20 AM »

got on xlights this morning and it looks like all my layout fixtures had zoomed up about 700%. I can find them on the lower left corner, but they are unrecognizable.
What did I do, and is there a fix?

7

Do You Need Help? Post it here / Re: xschedule videos

« on: November 25, 2019, 01:37:40 PM »

no settings menu in xscheduler, and looks like still a issue with it. I can add an fseq, but not a video file, nor can I access a video file in a previously established playlist, or one I had built before having this issue.
the video flicker/strobe started after updating to v.65, and I droped back to v.64 and still had the strobe.   

8

Do You Need Help? Post it here / Re: xschedule videos

« on: November 25, 2019, 09:30:12 AM »

well that sounds like some entertaining research... thanks Gil

9

Do You Need Help? Post it here / Re: xschedule videos

« on: November 25, 2019, 08:28:37 AM »

Downloaded v.66 this a.m., and wile it fixed the player window issue (thanks Keith), I still suffer the video strobe. like its trying unsuccessfully to open the player..
Any Idea's?

10

Do You Need Help? Post it here / xschedule videos

« on: November 23, 2019, 08:56:13 AM »

so, using videos through an actual projector, when played through xschedule the video doesn't actually start. it strobes on the xschedule video display screen, and on the projector screen, like its trying to start, but not quite kicking into gear. used videos for several years, and never had this problem before.  mp4 videos, ,1080 resolution,
2019.65 version. know they were having challenges with this version, wondering if this is part of it.

11

Xlights Setup / ccp set-up

« on: November 07, 2019, 01:19:19 PM »

I have a cut strand of ccp's on a fixture, and a little confused on how to enter them in the set-up page.
set-up page, lor set up drop down, do I add the actual number of channels of the strand in the #channel column, or do I use the full 150 ccp controller channels?

12

LOR / Re: ccb setup in xlights

« on: September 22, 2018, 01:49:27 PM »

Thanks again Gil

13

LOR / Re: ccb setup in xlights

« on: September 22, 2018, 12:47:09 PM »

So, after setting up all the lor networks off comm ports, if I want to add e131, do I start at universe 1?

14

The Water Cooler / e131 bridges

« on: September 11, 2018, 06:23:08 PM »

I'm looking for some e131 bridges if anybody is looking to unload any

15

LOR / Re: ccb setup in xlights

« on: September 11, 2018, 03:23:12 PM »

Thanks Gil, that would really make life easier.
I'll go bridge shopping and make that proposal.

Another question, in the set-up page, on the lor tab, in the lor controller definition, what are the address mode breakdowns?