Messages

1

Do You Need Help? Post it here / Re: Lor controller setting Layout Tab

« on: October 23, 2019, 01:52:31 PM »

Thanks a Bunch Trace !!

Joe Dudley
Silverthorne, Colorado

2

Do You Need Help? Post it here / Lor controller setting Layout Tab

« on: October 23, 2019, 11:21:48 AM »

In the Layout Tab, Controller Setting for LOR The program asks for port number, protocol, and channel number.
I am running XLIGHTS .59, through a Falcon F16v2R controller, to my LOR boxes configured for DMX channel numbers 1 through 48.
Do I use the Serial port number I am hooked into? Which is 2 ?
I can play my sequences when I output directly from computer, but when I use XSCHEDULE, about half of Pixels light up.
I have found some pixel settings which are wrong.
Thanks Joe

3

Do You Need Help? Post it here / Corrupt Keybindings file

« on: July 25, 2019, 01:17:16 PM »

Can you tell me how to send the developers my corrupt keybindings file? Where do I send it and how.
Thank you
Joe

4

Do You Need Help? Post it here / Cannot open Xlights on computer

« on: November 19, 2018, 10:38:39 AM »

I upgraded from .44 to .45 but when I tried to open Xlights got error message
"Unhandled,Unknown exception, Terminating application!".
I tried to go back and install .44 again, received same notification.
Enclosed screen capture.

5

General Software / Re: Another Windows 10 question

« on: March 04, 2018, 01:13:26 PM »

Took me a while but I did not have the files on auto sync. I transferred the RGB Effects and the Networks and Key bindings files and it worked.
Thanks

6

Xlights Setup / Change Show Directory

« on: February 12, 2018, 11:17:34 AM »

Am a Newbie, I am missing something. My current Show directory is C:\Users\Joe\Xlights3\2018.
Keith suggests saving all your files to a directory that does not end in a number. I want to Change the Directory to C:\Users\Joe\Xlights3\2018\Christmas.
How do I change the Directory so I can save my Setup and Models as well as my Images and Media files in the same place. I have gone through the manual and the videos, but I am missing it somewhere.
Thank you in advance.
Joe

7

General Software / Another Windows 10 question

« on: February 08, 2018, 12:35:25 PM »

When I Sequence on my Desktop running Window 7, and I save to Dropbox, the files do not show up in the directory, I cannot retrieve the files on my Laptop running Window 10.
When I sequence on my Laptop, and save to Dropbox, the files Do show up in the directory and  I can retrieve the files on my Desktop.
Any suggestions why?
Thank you in advance

8

Nutcracker Models / Re: Multiple colors in Whole House Preview

« on: February 23, 2017, 09:39:29 PM »

Dan you were spot on, ran sequence checker came up Overlapping channels
Thanks so much
Joe Dudley
Silverthorne CO

9

Nutcracker Models / Re: Multiple colors in Whole House Preview

« on: February 22, 2017, 09:21:12 PM »

This is a screen shot of my Whole House preview(Capture 2) and my sequence (Capture1). In the sequence the north tree ( tree on the right) should be on not everything. The roof lines, candy canes, windows and wreath,door outline only half on at that. Thank you for your patience, ( i hope i did this right)

10

Nutcracker Models / Re: Multiple colors in Whole House Preview

« on: February 22, 2017, 04:32:18 PM »

Newbee how do I get in on the training?
Thank you

11

Nutcracker Models / Multiple colors in Whole House Preview

« on: February 21, 2017, 12:39:58 PM »

Just starting in this AWESOME hobby, using 2016 51 Production , I setup my models in the layout tab but when I go to Sequencer tab, my whole house preview shows different colors in each model, example on a window model three sides will be blue the last side will be half blue and red. Then when I try to sequence say blue,then red, the playback on the house preview will not change when it is supposed to.
Thank you in advance for any help!