Messages

1

LOR / Re: SUP import not working as expected

« on: April 12, 2019, 08:14:47 AM »

After getting it to work on the matrix I had hanging on the wall, I carefully took it down and framed the matrix in pvc for added support. Now all the LEDs light up white. I understand that this could be a short a cross signal and v+, but I don't understand how something so mundane as moving the matrix would cause this. Could it be a failure within a pixel causing this? Any good troubleshooting methods, short of testing each pixel individually, for figuring out where the short is at?

2

LOR / Re: SUP import not working as expected

« on: April 11, 2019, 08:37:34 PM »

that did the trick, thank you very much!

3

LOR / Re: SUP import not working as expected

« on: April 11, 2019, 08:25:14 PM »

i have upload as you said several times now and I still get the invalid end universes and channels. not sure what to do now.

4

LOR / Re: SUP import not working as expected

« on: April 11, 2019, 08:10:31 PM »

here are the controller properties. I'm not sure why the end universes and channels are invalid.

5

LOR / Re: SUP import not working as expected

« on: April 11, 2019, 07:42:51 PM »

how is this?

6

LOR / Re: SUP import not working as expected

« on: April 11, 2019, 06:46:30 PM »

here are my model properties

7

LOR / Re: SUP import not working as expected

« on: April 11, 2019, 06:21:29 PM »

i dont think i zigzagged on the falcon controller as im not sure how to do that. I loaded setting to the falcon controller from xlights. how can i fix this? any ideas?

8

LOR / Re: SUP import not working as expected

« on: April 11, 2019, 05:47:41 PM »

How can I tell the controller this? By the way, it is one continuous string.

9

LOR / Re: SUP import not working as expected

« on: April 11, 2019, 05:24:30 PM »

My wiring view is attached, is there something else I need to do?

10

LOR / SUP import not working as expected

« on: April 11, 2019, 04:51:00 PM »

I imported a SUP file for a mega tree (its the Light of Christmas mega tree sequence). I loaded it to a matrix I have wired in a snake configuration. On xlights it looks file, but my pixels, all the odd columns are inverted. in xlights the node layout matches how my matrix layout is.

any ideas what is going on or what I can do to fix this???


Please help

11

Enhancement Requests / Re: copy and paste across multiple instances of Xlights

« on: April 07, 2019, 06:55:18 AM »

My bad, it wasn't working last night, but it is today. I must have not highlighted the sequence correctly last night.

12

Enhancement Requests / Re: copy and paste across multiple instances of Xlights

« on: April 07, 2019, 06:48:43 AM »

I did, but it didn't work.

13

Enhancement Requests / copy and paste across multiple instances of Xlights

« on: April 06, 2019, 09:42:43 PM »

I have no idea how complex something like this would be, but I think it would be cool to be able to copy and paste sections of sequences across multiple instances of Xlights. For instance, if I have 2 copies of Word open, I can highlight a paragraph in one instance of Word and paste it to the the document in other instance of Word I have open.

14

Do You Need Help? Post it here / singing tree

« on: February 07, 2019, 09:00:03 PM »

I have a mega tree I want to animate with a singing face. I can use import lyrics to import all the lyrics and break them down to sounds but how can I insert a resting face during breaks?

Thanks in advance for your help.

15

Do You Need Help? Post it here / Re: Models not showing up on sequence tab

« on: January 26, 2019, 05:58:44 PM »

Thanks! That did the trick.