This is the arduino sketch I am trying to use. Any thoughts/advice would be greatly appreciated.
_____________________________________________
// This code was written by Click that moment.
// To adapt the code to your case, just change this top section, with the #define lines.
// Includes the watchdog timer library
#include <avr/wdt.h>
// This sets how many channels will vixen be sending. Can be set to any number from 1 to 48 for Arduino Mega, and 1 to 18 for Arduino Uno.
#define CHANNEL_COUNT 8
// speed for the com port for talking with vixen. From 9600 to 115200. Use the same speed as set in Vixen.
#define VIXEN_COM_SPEED 57600
// Timeout waiting for serial input before going to random mode (in milliseconds).
#define TIME_OUT 1000
// If the relays turn On and Off opposite to Vixen sequence, change "#define MODE NOT_INVERTED" for "#define MODE INVERTED"
#define NOT_INVERTED 0
#define INVERTED 1
#define MODE NOT_INVERTED
// which pins control which channels
// You can change these assignment to use different pins, but be very careful to not repeat the same pin number for 2 channels.
// DO NOT use pings 0 and 1, as those are for the serial port to talk to the computer.
#define CH01 2
#define CH02 3
#define CH03 4
#define CH04 5
#define CH05 6
#define CH06 7
#define CH07 8
#define CH08 9
int channels[] = {CH01,CH02,CH03,CH04,CH05,CH06,CH07,CH08};
int incomingByte[CHANNEL_COUNT];
int i = 0; // Loop counter
volatile unsigned long timer_a = 0; // new line
//setup the pins/ inputs & outputs
void setup(){
// enable the watchdog timer with a time of 1 second. If the board freezes, it will reset itself after 1 second.
wdt_enable(WDTO_1S);
// specifically for the UNO
sei();
// initalize PWM Channels / Pins
for (i=0; i < CHANNEL_COUNT; i++){
pinMode(channels
, OUTPUT);
}
// set all the realys to off to start with
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
digitalWrite(channels, LOW);
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
digitalWrite(channels, HIGH);
}
}
testSequence();
// set up Serial according to the speed defined above.
Serial.begin(VIXEN_COM_SPEED);
}
void loop()
{
if (Serial.available() >= (CHANNEL_COUNT+2)) {
wdt_reset(); // resets the watchdog
timer_a = millis (); // new line
int uno = Serial.read();
if (uno == 126){
int dos = Serial.read();
if (dos == 33){
for (i=0; i < CHANNEL_COUNT; i++) {
// read each byte
incomingByte = Serial.read();
}
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
int value = incomingByte;
if (value <= 127) {
digitalWrite(channels, LOW);
}
else {
digitalWrite(channels, HIGH);
}
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
int value = incomingByte;
if (value < 127) {
digitalWrite(channels, HIGH);
}
else {
digitalWrite(channels, LOW);
}
}
}
}
}
}
// Random mode code. Random mode starts if no serial input has been received in TIME_OUT millisenconds
else {
wdt_reset(); // resets the watchdog
unsigned long diff = millis() - timer_a;
if (diff >= TIME_OUT) {
timer_a = millis ();
int random_a = 0;
for (i=0; i < CHANNEL_COUNT; i++){
random_a = random(0, 2);
if (random_a == 0) {
digitalWrite(channels, LOW);
}
else {
digitalWrite(channels, HIGH);
}
}
}
}
}
void testSequence(){
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
wdt_reset(); // resets the watchdog
digitalWrite(channels, HIGH);
delay (500);
digitalWrite(channels, LOW);
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
wdt_reset(); // resets the watchdog
digitalWrite(channels, LOW);
delay (500);
digitalWrite(channels, HIGH);
}
}
}
Show Posts