Messages

1

Do You Need Help? Post it here / Re: xSchedule failure codes

« on: December 25, 2019, 11:09:02 AM »

My bad, I should say the failures just keep rolling up. I just checked again and the failures has increased.
I checked the logs and it shows error with channels..

Where do I go to start trying to find out why this is happening.

song XXXX1 with 7564 channels when only 7560 channels are configured
song XXXX2 with 14976 channels when only 7560 channels are configured
song XXXX3 with 7564 channels when only 7560 channels are configured
song XXXX4 with 7564 channels when only 7560 channels are configured
song XXXX5 with 7564 channels when only 7560 channels are configured
song XXXX6 with 7564 channels when only 7560 channels are configured
song XXXX7 with 7564 channels when only 7560 channels are configured

Everything should be 7560, that what shows in setup tab and layout tab.

2

Do You Need Help? Post it here / xSchedule failure codes

« on: December 25, 2019, 08:59:28 AM »

Checked my xScheduler this morning and it shows failure with codes of 145 on one controller and 554 on another.
where can I find a list of what these codes mean? So I can fix.

3

General Software / Re: Xlight Preview different once it hits Display

« on: November 25, 2019, 04:16:17 PM »

Created new show folder and animation and only built one tree with 8 channels. I tried 0ne spiral effect it it light up all models on all 16 channels and the effect was different than what I asked for.
I did look at the live date on the web page to the controller and it showed packet on the first 8 channels As I would of expected. Seems to be broadcasting across all channels.

4

General Software / Xlight Preview different once it hits Display

« on: November 24, 2019, 08:58:03 PM »

I have a mega tree and a few other smaller trees in the display. In the preview I put on snow fall but when I run on display it is total different. Solid colors are fine and some patterns work. It seems hit and miss. Tried looking at addressing but it appears ok.
I also can not use xlights to run test mode.
If I pick whole display it works but if I try t narrow down to one item I get nothing.
Using Falcon 16V3  with the latest firmware update.

Any ideas on where to start. Or why this maybe happening

5

Do You Need Help? Post it here / Re: Alphpix 16 need help !!!

« on: June 28, 2016, 07:45:39 PM »

Yes no problem connecting thur web browser. But it looks like you can change color sequence but it for the whole controller not each univ.

6

Do You Need Help? Post it here / Re: Alphpix 16 need help !!!

« on: June 28, 2016, 07:13:11 PM »

Firmware 1.04 Nov 2015
The thing is it moves with the light strip. Can you program each univ with a different color sequence.

7

Do You Need Help? Post it here / Alphpix 16 need help !!!

« on: June 28, 2016, 06:59:03 PM »

Setting up lights for the 4th. I have 7 Univ programmed up. When I connect the lights 6 of the univ come up and flash G/R/B and 1 univ flashes B/R/G. I can move the univ this is backwards to a different univ and still same backward colors. Can you set each univ to a different color comb output. Got this color order by going thur the test mode on the controller. Any help, my time is running out.

running 2811 strip lights

8

Xlights Setup / Re: Setup question :why after i save a sequence it always adds channels

« on: September 20, 2014, 08:20:16 AM »

see attached

[attachment deleted by admin]

9

Xlights Setup / Re: Setup question :why after i save a sequence it always adds channels

« on: September 20, 2014, 08:09:19 AM »

<?xml version="1.0" encoding="UTF-8"?>
-<Networks computer="MATT">
<network MaxChannels="450" BaudRate="1" ComPort="MULTICAST" NetworkType="E131"/>
<network MaxChannels="450" BaudRate="2" ComPort="MULTICAST" NetworkType="E131"/>
<network MaxChannels="300" BaudRate="3" ComPort="MULTICAST" NetworkType="E131"/>
</Networks>

Thanks for taking a look.

10

Xlights Setup / Setup question :why after i save a sequence it always adds channels

« on: September 18, 2014, 03:09:09 PM »

I go through the set up with Univ 1 1-450 Univ 2 451-900 & Univ 3 900 -1200
I then go an make a sequence and when I save it say it added 300 channels and says I need to review setup.
Where have I messed up?