1
Nutcracker Effects / Re: Spiral Speed
« on: December 02, 2020, 06:53:47 PM »
Assume you will see the break between them. I'll try. Otherwise, I'll find a alternative.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Nutcracker Effects / Spiral Speed
« on: November 30, 2020, 06:41:18 PM »
I want a 5-10 minute spiral. At 2.5 minutes with movement all the way up at 20, it's almost stopped.
Anyway to speed these up?
Anyway to speed these up?
3
Nutcracker Effects / Re: Fan speed on longer sequences
« on: December 09, 2018, 03:46:39 PM »
Just one after the other?
4
Nutcracker Effects / Fan speed on longer sequences
« on: October 27, 2018, 07:22:41 PM »
I need to make a 4 hour sequence and want to have the fan effect on a megatree for the entire period of time. it obviously spreads the settings across the whole time so it appears to just sit still the whole time. Even on 5 seconds, it slows down at the end and stops and then restarts.
Is there a way to get the fan effect working at "normal speeds for a extended period of time instead of time?
Is there a way to get the fan effect working at "normal speeds for a extended period of time instead of time?
5
General Software / text Scrolling Multiple Lines - Sync two layers
« on: November 30, 2017, 12:12:28 PM »
I am trying a simple text effect with two layers. I want to scroll Merry on top and Christmas on bottom. I have them scrolling but due to the difference in word length they do not stay synced up. I have played with the offsets but am not getting it to stay consistent. any tips?
6
Nutcracker Effects / Re: Changing effect color
« on: November 28, 2017, 06:16:40 PM »
Yes, found a thread below and feel dumb now 
7
Nutcracker Effects / Changing effect color
« on: November 28, 2017, 06:04:56 PM »
I want to change the white color in the Spiral effect to a more warm white color. I have a start with the actual RGB mix, but not sure how to change the white to another color (or just add a new color).
Thanks!
Thanks!
9
Xlights Setup / Zig Zag Config
« on: November 18, 2017, 11:18:22 PM »
I am upgrading to a 32 string tree this year from 16. I am making sure I understand the Wiki right here. From the wiki:
I have 16 X 50 strings for my mega tree. How do I get the xlights to do a zig zag on the preview window?
If you have 16 strings, and string 1 starts from the bottom, 2 from the top, 3 from the bottom etc , in that case, make your tree model so that the strings are 2x the actual length and then configure the strings to have 2 strands per string. So, the model is 8 strings of 100 with 2 strands.
So for 32 strands where every other strand is reversed, I just need to have 16 strings with 100 nodes and 2 strands?
I have 16 X 50 strings for my mega tree. How do I get the xlights to do a zig zag on the preview window?
If you have 16 strings, and string 1 starts from the bottom, 2 from the top, 3 from the bottom etc , in that case, make your tree model so that the strings are 2x the actual length and then configure the strings to have 2 strands per string. So, the model is 8 strings of 100 with 2 strands.
So for 32 strands where every other strand is reversed, I just need to have 16 strings with 100 nodes and 2 strands?
Pages: [1]