Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mt2525

Pages: [1]
1
Lilia Sequences / Re: Lilia Sequences Info
« on: November 05, 2018, 08:16:36 PM »
So are Lilia's sequences still available? And can they be seen somewhere?

2
Do You Need Help? Post it here / Re: Folder with sequences
« on: April 02, 2017, 12:46:17 PM »
I created a new folder in documents and pointed xlights to it and after searching my c drive I finally located the folder that had what I had done so far in xlights. I had to go to users\myname\appdata\local\virtualstore\program files(x86)\xlights and there it was. Copied it to new folder in documents and all is well. Thanks for your time

3
Do You Need Help? Post it here / Re: Folder with sequences
« on: April 01, 2017, 10:07:36 PM »
I am in the x86 program files.....as shown in the screen shot. Where should I put the show and media folder if not in the x-lights folder?

4
Do You Need Help? Post it here / Folder with sequences
« on: April 01, 2017, 08:12:36 PM »
My show directory and media directory point to the same folder......and if I open x-lights and ask it to open a sequence I started it shows the folder......but if I go to my c drive and follow the path, I get to the x-lights folder but it doesn't show the folder where my sequences are suppose to be. What am I missing?

5
Did that and have 32 models that I numbered Fence 1, Fence 2 etc. Then created a group called fence and added all 32.  Next question is when I start a new sequence I don't want to see all 32 pieces of the fence listed on the side of the sequence. How do I not show them?

6
Is there a way to to take the first model and reproduce it 32 times instead of making 32 individual ones?

7
Now I'm trying to set up a model for my fence which is in about 150 feet down each side of property and 150 feet in with house in middle. On the fence is 32 pieces of rope lighting with each piece about 18 feet long and controlled by one channel of renard. So 16 pieces of rope lighting on left side of house (channels 1-16 ) and 16 pieces on right side (channels 17-32). How would I set this up? Again thanks to Gilrock for help on setting up Mega tree

8
Thanks and I'm sure there will be more questions down the road.

9
Do You Need Help? Post it here / Setting up Mega tree channel numbers.
« on: March 03, 2017, 10:47:54 PM »
Moving over from Vixen and the way my 16 strand, 50 pixels per strand mega tree ... except strands 15 and 16 ...is configured is this....using a sandevices 682.... ports 1-12 set for 50 pixels per strand and ports 13-16 set for 100 pixels per strand because strands 15 and 16 feed my star on top of tree. Strand 15 first 50 pixels for leg 15 and second 50 pixels to outer star and strand 16 feeds first 50 for leg 16 and 50 for middle and inner star... middle star...30 nodes and inner star 20 nodes. To get this to work in vixen I set up legs 13 and 14 to have the first 50 pixels for each leg and second 50 as blank.
Strands 1-12.. channels 1-1800
Strand 13..... ..channels 1801-1950
                      1951-2100 blank
Strand 14....... channels 2101-2250
                       2251-2400.....blank
Strand 15........channels 2401-2550
Outer Star.......channels 2551-2700
Strand 16........channels 2701-2850
Middle Star......channels 2851-2940
Inner Star........channels 2941-3000

Now the question is how do I configure this in x-lights?
Thanks for any input...

Pages: [1]