Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Bartlettguy67

Pages: [1] 2
1
Do You Need Help? Post it here / Re: XScheduler - Resolved
« on: November 29, 2020, 11:41:36 AM »
Just needed to render all the sequences.

2
Do You Need Help? Post it here / XScheduler - Resolved
« on: November 28, 2020, 05:01:36 PM »
When I run the lights in xlights on a sequence, they output correctly to everything.    But when xscheduler starts, the first two candy canes don't light up, but the third one in the group does.  So they are getting data and power.   My matrix is also putting out garbage.

Why would they output correctly in Xlights, but when the Xschedule is going night they don't work?

I'm running 2020.49.

TIA

3
Bugs in xLights/Nutcracker / Re: Unable to change Max number of snowflakes
« on: September 08, 2020, 06:38:49 PM »
Thanks

4
Bugs in xLights/Nutcracker / Unable to change Max number of snowflakes
« on: September 07, 2020, 07:50:57 PM »
You're not able to change the max number of snowflakes in update 34 and 35.

It's dimmed out and you're unable to change it.


5
Bugs in xLights/Nutcracker / Re: Update 2018.35
« on: October 06, 2018, 07:07:06 PM »
That worked.  My cane rotation was at -180 and I changed it back to zero,  installed the update and that did it.

Thanks for the help!

6
Bugs in xLights/Nutcracker / Update 2018.35
« on: October 05, 2018, 06:56:37 PM »
I just downloaded the 2018.35 and my candy cane models turned upside down.   I had to re-install 2018.34 and everything is fine.    Has any other issue with models been reported after installing 2018.35?

7
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 29, 2018, 08:02:06 PM »
Here is the attachment of what I had to change.    I had to rename the Candy Cane groups.  Once I did that, they all worked fine.

8
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 26, 2018, 06:48:59 PM »
I'm not sure what happened.  I had a model setup running 12 candy canes together, all doing the same thing.  Then I had them broken down into groups of three.  For some reason it didn't like the names that I had, so I renamed them and it's working now. 

Before I couldn't even get xlights to work on the versions between 2017.44 and 2018.3. 

I'm glad to get it working and thanks for looking to see what could have been the issues.

9
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 22, 2018, 08:08:43 PM »
I just downloaded 2018.3.  I had to tweak my models because Xlights could not figure the start channel on 4 groups.  Once I did that, 2018.3 is working.

10
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 18, 2018, 08:11:22 PM »
I know this might sound like a dumb question, how do I get into zoom?

11
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 16, 2018, 07:53:26 PM »
Tried that and it still didn't work.  Nothing will work above the 2017.44.

This is a new desktop with windows 10.    I'm not sure why it's not working.

12
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 15, 2018, 07:19:52 PM »
How can I start it in a new show folder? 

I'm willing to try that to see if it'll work.  I can't get xlights to open.

13
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 15, 2018, 07:07:10 PM »
Yes, still would not open.

I just downloaded 2018.2 and it crashes also.  It says xlights.exe has stopped working. 

I just downloaded 2017.44 and it works fine. 

I don't know where the issue could be.

14
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 12, 2018, 06:39:30 PM »
I tried that and it still will not open. 

The most current one that I can download and work is the 2017.44.


15
Do You Need Help? Post it here / Re: 2018.1 xlights crashing
« on: January 11, 2018, 09:20:56 PM »
I've attached the three files.

Thanks for everyone's help.

Pages: [1] 2