1
Do You Need Help? Post it here / Re: Xschedule Issue with output of lights
« on: December 03, 2018, 12:09:00 PM »
The batch render solved the issue, Thanks again Keith.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Do You Need Help? Post it here / Re: Xschedule Issue with output of lights
« on: November 29, 2018, 08:38:59 PM »
Keith, I did not know about the batch render option, just learned another tip, thank you, I will try that.
3
Do You Need Help? Post it here / Re: Xschedule Issue with output of lights
« on: November 29, 2018, 12:43:02 PM »
Yes Both pointing to same Directory, I will Render and save each sequence tonight to make sure, not sure
if I did that last night, So If you don't save the sequence after rendering, then reopen later, would the sequencer
make you re-render before sequence would play on the house model, or actually play on your display?
Thay was an issue last night as well.
if I did that last night, So If you don't save the sequence after rendering, then reopen later, would the sequencer
make you re-render before sequence would play on the house model, or actually play on your display?
Thay was an issue last night as well.
4
LOR / Re: Matrix not keeping up with sequence.
« on: November 29, 2018, 12:35:18 PM »
Other controllers are on E1.31 network, all work great, just these 2 pixies have issues, I tried last night with
both pixies on the high speed adapter, and same result, cant keep up, I will put each screen on there own
lor adapter tonight to see if any better result.
Thanks Guys, If I cant get going correctly tonight, I am ordering 2 E1.31 controllers to replace the Pixies.
both pixies on the high speed adapter, and same result, cant keep up, I will put each screen on there own
lor adapter tonight to see if any better result.
Thanks Guys, If I cant get going correctly tonight, I am ordering 2 E1.31 controllers to replace the Pixies.
5
Do You Need Help? Post it here / Xschedule Issue with output of lights
« on: November 29, 2018, 10:10:19 AM »
I had my show already running this last week no issues besides my Pixies cant keep up, thats another issue.
but last night I added a new sequence to my show, then added it to my shedule and when all of my sequences
are playing thru xschedule the channels are off, my verticals are overlapping into my horizontal's almost like
my setup is off, but when I go into the sequencer and use output to lights, these sequences play perfectly.
what happened?, is there something I need to do, I completely deleted the schedule and setup in xschedule
multiple times and still same effect.
please help.
but last night I added a new sequence to my show, then added it to my shedule and when all of my sequences
are playing thru xschedule the channels are off, my verticals are overlapping into my horizontal's almost like
my setup is off, but when I go into the sequencer and use output to lights, these sequences play perfectly.
what happened?, is there something I need to do, I completely deleted the schedule and setup in xschedule
multiple times and still same effect.
please help.
6
LOR / Matrix not keeping up with sequence.
« on: November 28, 2018, 04:52:52 PM »
I decided months back to switch from LOR to Xlights this year, along with changing my whole display to
smart pixels, I've spent hours on youtube, and xlights videos and its helped tremendously. I have a problem
with both my Matrices not keeping up, I have each of them running on there own Pixie16, 1 is 24x50, running off of 12 ports, the other is 25x28 running off of 7 ports of the other controller, the matrix is the only props connected to these Pixie controllers. I have them running on 1 network, 500k, Enhanced, I have ordered LOR's RS485-HS Adapter, but not confident that is going to help with the lagging going on. Is there
something else I need to change, add, Beside replacing the controllers right now. I had these plugged in
and ran them thru xlights prior to the show and didnt see any problems, but that was before the rest of the
contollers were connected and running.
smart pixels, I've spent hours on youtube, and xlights videos and its helped tremendously. I have a problem
with both my Matrices not keeping up, I have each of them running on there own Pixie16, 1 is 24x50, running off of 12 ports, the other is 25x28 running off of 7 ports of the other controller, the matrix is the only props connected to these Pixie controllers. I have them running on 1 network, 500k, Enhanced, I have ordered LOR's RS485-HS Adapter, but not confident that is going to help with the lagging going on. Is there
something else I need to change, add, Beside replacing the controllers right now. I had these plugged in
and ran them thru xlights prior to the show and didnt see any problems, but that was before the rest of the
contollers were connected and running.
7
LOR / Re: Crash upon hitting PLAY
« on: September 22, 2018, 04:21:25 PM »
I have the identical problem you just described, I was on here looking to figure out what I had done wrong.
I connected mine to LOR's S5 software to test, and it works fine. I am wondering if its a problem with xlights software, or are we not setting it up correctly in xlights. My prop is also a 24x50 Matrix, with 12ea 100 pixel string
folded over. Hope there is a resolution to this issue real soon.
I connected mine to LOR's S5 software to test, and it works fine. I am wondering if its a problem with xlights software, or are we not setting it up correctly in xlights. My prop is also a 24x50 Matrix, with 12ea 100 pixel string
folded over. Hope there is a resolution to this issue real soon.
Pages: [1]