Author Topic: How to adjust light intensity for displays  (Read 3627 times)

Offline blk69

  • Newbie
  • *
  • Posts: 16
    • View Profile
How to adjust light intensity for displays
« on: November 21, 2016, 10:36:28 AM »
Total newbie here.  Have put together a few Xlight sequences.  Planning on running on FFP with Rasp Pi ver 3.0.  Read numerous posts that LED's running at 50% vs 100% are very difficult for the human eye to distinguishes the difference.  See in Xlights under the test tab can adjust each colors light level.

My question is how (or if) I can adjust the light level for all my effects?  Still very green, hopefully this was just a button or selection I missed.  Thank you in advance for any help on this issue.

Offline Dave Nibeck

  • Jr. Member
  • **
  • Posts: 97
    • View Profile
Re: How to adjust light intensity for displays
« Reply #1 on: November 21, 2016, 04:32:34 PM »
Set intensity for each model in layout.

Sent from my Nexus 6P using Tapatalk


Offline MrChristmas2000

  • Sr. Member
  • ****
  • Posts: 293
    • View Profile
Re: How to adjust light intensity for displays
« Reply #2 on: November 21, 2016, 06:50:44 PM »
Some hardware controllers like a Falcon F16V2 have the ability to control the intensity from within the controllers settings.

Offline aERonAUtical1996

  • Newbie
  • *
  • Posts: 15
    • View Profile
Re: How to adjust light intensity for displays
« Reply #3 on: November 21, 2016, 08:36:12 PM »
Set intensity for each model in layout.


Are you referring to the Brightness control in the Dimming Curves?  Assuming setting it to -50 is setting it to 50% as the highest level.

Offline kevinp

  • Sr. Member
  • ****
  • Posts: 373
    • View Profile
Re: How to adjust light intensity for displays
« Reply #4 on: November 21, 2016, 09:23:03 PM »
Quote
Are you referring to the Brightness control in the Dimming Curves?  Assuming setting it to -50 is setting it to 50% as the highest level.

Yes, setting the dimming curve to -50 will lower the brightness of the model for the entire sequence.
« Last Edit: November 21, 2016, 09:28:04 PM by kevinp »
Kevin Pankratz
Blaine MN

Offline blk69

  • Newbie
  • *
  • Posts: 16
    • View Profile
Re: How to adjust light intensity for displays
« Reply #5 on: November 21, 2016, 09:26:34 PM »
Will look into all the suggestions.  Just powered my arches, after 40 pixels my whites are pink.  Not so good.  Hoping reducing power will help with voltage drop.

Offline kevinp

  • Sr. Member
  • ****
  • Posts: 373
    • View Profile
Re: How to adjust light intensity for displays
« Reply #6 on: November 21, 2016, 09:29:07 PM »
Will look into all the suggestions.  Just powered my arches, after 40 pixels my whites are pink.  Not so good.  Hoping reducing power will help with voltage drop.

That should help.  You may need/want to power inject from the other end of the arch too.
Kevin Pankratz
Blaine MN

Offline MrChristmas2000

  • Sr. Member
  • ****
  • Posts: 293
    • View Profile
Re: How to adjust light intensity for displays
« Reply #7 on: November 22, 2016, 05:57:36 AM »
What controller are  you using.
What pixels are you using?
Usually when pixels start changing color or flickering down a string it is as stated most likely the need for power injection?

Problems after 40 pixels seems like a very rapid voltage drop though.
Is your power supply set to 12volts, if 12v pixels, 5v if 5v pixels. Many power supplies come under adjusted for proper voltage output.

Offline blk69

  • Newbie
  • *
  • Posts: 16
    • View Profile
Re: How to adjust light intensity for displays
« Reply #8 on: November 23, 2016, 11:26:40 AM »
What controller are  you using.
What pixels are you using?
Usually when pixels start changing color or flickering down a string it is as stated most likely the need for power injection?

Problems after 40 pixels seems like a very rapid voltage drop though.
Is your power supply set to 12volts, if 12v pixels, 5v if 5v pixels. Many power supplies come under adjusted for proper voltage output.

Using 5m ws2811 16 led/m strips.  Power supply is a 350w meanwell 12v.  Strips are 12v to.  I have 5 to 10' of 18 gauge cable between the arches to space them out.  Going to increase power injection and mess around with the dimming curves in Xlights (original thought that option was limited to light fluctuation on the effects....not overall light power/intestity.

Offline Gilrock

  • Supporting Member
  • Hero Member
  • *
  • Posts: 6946
    • View Profile
Re: How to adjust light intensity for displays
« Reply #9 on: November 23, 2016, 11:46:04 AM »
You skipped his first question which was the most important because some controllers allow you easily adjust power output.  You need to tell us what controller is running the pixels.

Offline blk69

  • Newbie
  • *
  • Posts: 16
    • View Profile
Re: How to adjust light intensity for displays
« Reply #10 on: November 24, 2016, 09:14:47 PM »
You skipped his first question which was the most important because some controllers allow you easily adjust power output.  You need to tell us what controller is running the pixels.

I am not using a controller, running two outputs directly from the Rasp Pi. 

Offline Gilrock

  • Supporting Member
  • Hero Member
  • *
  • Posts: 6946
    • View Profile
Re: How to adjust light intensity for displays
« Reply #11 on: November 24, 2016, 10:39:02 PM »
Well then the first answer you got is the solution.  Create a dimming curve for each model in Layout.

Offline Dave Nibeck

  • Jr. Member
  • **
  • Posts: 97
    • View Profile
Re: How to adjust light intensity for displays
« Reply #12 on: November 25, 2016, 02:06:15 AM »
Don't forget to re-render and save each sequence to generate new fseq files.

Sent from my Nexus 6P using Tapatalk


Offline MrChristmas2000

  • Sr. Member
  • ****
  • Posts: 293
    • View Profile
Re: How to adjust light intensity for displays
« Reply #13 on: November 25, 2016, 07:30:10 AM »
Actually technically the Pi is a controller as much as any other piece of hardware.

Offline blk69

  • Newbie
  • *
  • Posts: 16
    • View Profile
Re: How to adjust light intensity for displays
« Reply #14 on: November 26, 2016, 09:18:12 AM »
Actually technically the Pi is a controller as much as any other piece of hardware.

I have the new pi hat from falcon.  It's has fused outputs, powers the pi and programmable thru fpp.  Never used a controller (Newbe) assume this has be be very close.