« previous next »
Pages: [1]   Go Down

Author Topic: Visualizer question.  (Read 1989 times)

Offline Jeff Millard

  • Newbie
  • *
  • Posts: 29
    • View Profile
Visualizer question.
« on: March 10, 2020, 06:33:48 PM »
Keith, I have a 4 port E1.31 bridge I'm using to connect around 90 A/C channels, but only to one of the ports. It's a large portion of my display. Is there any intent to make the Visualize work for this type of controller? Right now it's just a blank square, and the models are all on the right tab just wishing they could be dragged and dropped onto the controller.

Jeff
Logged

Offline keithsw1111

  • Administrator
  • Hero Member
  • *****
  • Posts: 2733
    • View Profile
    • Kellyville Christmas Lights
Re: Visualizer question.
« Reply #1 on: March 10, 2020, 06:37:47 PM »
Only if I have the details of them. If it is web configurable I would also want one to test with.

It is hard to support anything that none of the developers have access to.
Logged

Offline Jeff Millard

  • Newbie
  • *
  • Posts: 29
    • View Profile
Re: Visualizer question.
« Reply #2 on: March 11, 2020, 03:06:01 AM »
Thank you. It's the RPM 4-port board from DIYC. I doubt it would be worth your time. I'll build a second one and send it to you if you'd like, but I understand if you're not interested.

Jeff
Logged

Offline keithsw1111

  • Administrator
  • Hero Member
  • *****
  • Posts: 2733
    • View Profile
    • Kellyville Christmas Lights
Re: Visualizer question.
« Reply #3 on: March 11, 2020, 04:39:52 AM »
Does it have a web ui. If it does then I am happy to build for it. If not then maybe just describe it?s config.
Logged

Offline Jeff Millard

  • Newbie
  • *
  • Posts: 29
    • View Profile
Re: Visualizer question.
« Reply #4 on: March 11, 2020, 07:14:30 AM »
It's similar to, and based on the early Sandevices E681.

This is the wiki for the 4-port bridge:

http://www.doityourselfchristmas.com/wiki/index.php?title=RPM_4_Port_e1.31_Bridge

Just below the image is a note with a link to the more common 6-port version of the board.

If you need the hardware for the 4 -port, I can toss one together in a couple days and ship it to you. If you need the 6-port it'll take me a couple weeks to gather parts and board. Say the word and I'm on it.

Jeff
« Last Edit: March 11, 2020, 07:17:24 AM by Jeff Millard »
Logged

Offline keithsw1111

  • Administrator
  • Hero Member
  • *****
  • Posts: 2733
    • View Profile
    • Kellyville Christmas Lights
Re: Visualizer question.
« Reply #5 on: March 11, 2020, 02:11:13 PM »
If you send me one I will build the upload. For the 6 port likely you could just send me some files first to verify it is largely the same.
Logged

Offline Jeff Millard

  • Newbie
  • *
  • Posts: 29
    • View Profile
Re: Visualizer question.
« Reply #6 on: March 12, 2020, 10:33:22 AM »
Thank you! I should have one built by mid next week. DM me an address to send it to and I'll ship it as soon as it's completed.

Parts I didn't have are coming Monday. I hope the RS485 line drivers I ordered work. If not, I'll swap the ones on my board out to get it shipped.

Jeff
Logged

Offline Jeff Millard

  • Newbie
  • *
  • Posts: 29
    • View Profile
Re: Visualizer question.
« Reply #7 on: March 12, 2020, 10:43:11 AM »
Quote from: keithsw1111 on March 11, 2020, 02:11:13 PM
For the 6 port likely you could just send me some files first to verify it is largely the same.

The manual for 6-port is located here:

http://doityourselfchristmas.com/wiki/index.php?title=E1.31_Bridge#Configuring_the_E1.31_Bridge

I couldn't find any other files but firmware hex.

Jeff
Logged
Pages: [1]   Go Up
« previous next »