Messages

1

Show Assets / Thats Christmas to me pentonix

« on: November 30, 2019, 05:08:10 PM »

Looking for megatree sequence for this song, found an old post from 2015, but attachment is gone, wondered if anyone has done this  song and willing to share. I have a 16 strand 75 pixel per strand 180 tree. Would be greatly appreciated if willing to share. In my second year so dont have anything to trade.

2

Show Assets / Thats Christmas to Me Pentatonix

« on: March 25, 2019, 02:31:41 PM »

Looking for megatree sequence for this song, found an old post from 2015, but attachment is gone, wondered if anyone has done this  song and willing to share. I have a 16 strand 75 pixel per strand 180 tree. Would be greatly appreciated if willing to share. Trying to get my sequencing done before the day the show starts this year! Ah , i always start with this same thought.... never seems to come to fruition!

3

LOR / Re: Running LOR controllers in xlights

« on: November 19, 2018, 05:07:20 AM »

So i did the test, and now started adding fseq one by one and now it all works, even sending data through my lor ELL wireless linkers, so i i don't know what the issue was but im going to build a schedule and see how it goes. Thanks si much fir all your help, this site is great for all the help people offer even in this busy time!

4

LOR / Re: Running LOR controllers in xlights

« on: November 18, 2018, 01:49:14 PM »

So I did what you suggested and set up the test,  my lor props are a mix of led and incans, as well as some RGB floods. I set it up for value 1, and value 2 with no lights, but when i changed to A,B,C and A, B,C All all lor controllers lights, LED, Incans and RGB as well as my e131 tree and star come on , although they flash on and off. So i am not sure what this means , since there is no FSEQ in in, what is wrong with my FSEQ files?

5

LOR / Re: Running LOR controllers in xlights

« on: November 18, 2018, 09:50:04 AM »

Ok ao i deleted all my playlists and started from scratch , rebooted my computer, and just made an all on all channel sequence in xlights. Opened it in xschedule, and ran it and about 1/2 of my lor controllers lights came on, i was so excited, so i ran it again so I could run out side and see exactly what was on and what wasnt, and none of them came on this time. I looked at the log and I dont see any difference but have attached it to this post, thoughts?

6

LOR / Re: Running LOR controllers in xlights

« on: November 17, 2018, 08:53:15 AM »

Im running 2018.44, when i look at the log, and im in no way claiming to have any computer knowledge, it seems like the packets of data start, for a 1 or 2 packets then stop

7

LOR / Re: Running LOR controllers in xlights

« on: November 16, 2018, 08:23:39 PM »

I am new to all of this, i am not familiar with zoom and how to get to it?

8

Do You Need Help? Post it here / Re: Xscheduler issue

« on: November 16, 2018, 08:21:27 PM »

So i deleted all my playlists to start clean, made an all lights on animation sequence in xlights, went to xschedule and made a playlist with just that in it and played it. My e131 tree and star came on, but no LOR channels came on. I tested my lor controllers through LOR and all the lights come on, I have attached the log

9

Do You Need Help? Post it here / Re: Xscheduler issue

« on: November 16, 2018, 05:49:31 PM »

Yes it has lor output to all 144 channels, i am not familiar with an advanced playlist? How do you set it up?

10

LOR / Re: Running LOR controllers in xlights

« on: November 15, 2018, 06:46:36 PM »

Any suggestions would be appreciated, and thanks for looking at what I have so far, Im at a loss as what to do next , i was hopeful to get it up this year, but i have my schedule built in LOR scheduler as well and all sequences in LMS files as well, so I am not crunched to get this done for this years lights, but I do want to transition to all xlights

11

LOR / Re: Running LOR controllers in xlights

« on: November 15, 2018, 05:33:45 PM »

Check schedule finds no errors

12

LOR / Re: Running LOR controllers in xlights

« on: November 15, 2018, 05:05:33 PM »

screenshots from xlights and xschedule, looks the same folder to me? Attacheg logfile from brief test, error message [WARN] Frame interval greater than 200% of what it should have been [50] 142 shows up many times

13

LOR / Re: Running LOR controllers in xlights

« on: November 15, 2018, 03:07:44 PM »

The issue I am having is in xschedule, and i have posted that thread under problems, when i am in xlights, and run test and check my lor lights, under the standard tab no lights function, if i use the rgb tab, then lor lights(which are not RGB) come on . If a bring up a sequence in xlights and play it with the lights output on, the LOR controllers work as expected. I didnt know if this was an issue or not, chalking it up to my unfamiliarity with xlights, but i have set up shows in xschedule and no data is showing up in the log going out to the LOR controllers, even though they work in xlights when I play the sequence. I am just checking to see if my setup is right or not, as the source of my xsxhedule issue

14

LOR / Running LOR controllers in xlights

« on: November 15, 2018, 01:16:25 PM »

I am trying to use xlights to "run" LOR controllers. I have 6 CTB16PC controllers and 2 CMB24 RGB floodlight controllers for a total of 144 channels. I also have a Pixel tree and star running  on E131. I have attached screenshots of my setups to see if I have done this correctly. I have watched numerous videos, and have seen people describe it different ways. I will be outputting to my LOR controllers and CNB24 RGB through the lightorama usb485b with booster, and cat 5 to my e131.

15

Do You Need Help? Post it here / Re: Xscheduler issue

« on: November 15, 2018, 05:54:43 AM »

I have looked and it is black writing C:\Users\Michael|Documents|Light-O-Rama|Sequences  I have attached screenshots and the log